TX - Hager. In the Power up OFF state the lighting will not be energised and the sensor will not operate during warm up period. It's a community-based project which helps to repair anything. Automatic mode presence detection In this mode the light is controlled by motion in the detection area and ambient light levels. It allows the same functionality as the wallswitch. A KNX pushbutton linked to the product makes it possible to reverse the lighting output state. Betriebsarten Der Melder bietet 2 Betriebsarten: 
| Uploader: | Zulkir |
| Date Added: | 22 April 2007 |
| File Size: | 30.58 Mb |
| Operating Systems: | Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X |
| Downloads: | 85377 |
| Price: | Free* [*Free Regsitration Required] |
Once the sensor is activated, it will hold the lights on whilst there is still occupancy and for the time out period afterwards.
The most comprehensive KNX catalogue with > 15.000 available products
Lighting time delay is restarted after each detection. Das Licht wird sofort nach Wiederherstellung der Stromzufuhr eingeschaltet.

Betriebsarten Der Melder bietet 2 Betriebsarten: Automatik-Einstellungen Potentiometer Lux auf Autotest stellen. If the sensor detects occupancy whilst the ambient light level is below the required Lux level, the lights will be activated. The green or red LED behind the lens is on for 2 seconds after detection. Auto Settings Put the Lux potentiometer on "auto test".
It allows the same functionality as the wallswitch. Product description and operation principles Occupancy sensors 10 05 are presence detectors designed to detect low amplitude movements movements from body or arms. Test and validate the detection zone. The occupancy sensor measures the brightness in the room on a continuous basis and compares it to the level preset on the potentiometer 1 or by means of the remote control 40 02 by ETS parameter.
ROOM THERMOSTAT
Installateur-Einstellungen Test und Kontrolle des Meldebereichs. The output remote KNX load is switched during 2 s. Betriebsart Test ist 2 Min. This state is maintained for the time period dqtenbank by the potentiometer 2 or the remote control 40 Nach jedem Meldevorgang wird die Betriebsart Test 2 Minuten lang aktiviert. It's a community-based project which helps to repair anything. Once the sensor has deactivated the lights, it will require another input from the berkeer or the remote control to switch the lights on.
II IK 04 Protection degree: There is a time out during 2 minutes which is reactivated after each detection.
Nach der Programmierung das Potentiometer in eine andere Stellung bringen. In case of detection, if the ambient light level khx, the photocell will not turn off the light.
INTERRA Akıllı Ev, Otomasyon Sistemleri
If necessary, the level has to be adjusted by potentiometer or remote control. These products are part of the tebis installation system. The range may be reduced if walking towards the sensor. A KNX pushbutton linked to the product makes it possible to reverse the lighting dqtenbank state.
In case of detection, the light in automatic mode remains on during the time delay; otherwise the light is switched off. Detection is by means of the pyroelectric IR sensor berkrr under detection lens.

Test Mode This mode makes it possible to validate the detection area. Verbundschaltung mehrerer Melder Um den Erfassungsbereich zu erweitern, kann der Melder in Verbindung mit einem oder mehreren Meldern eingesetzt werden. Do you need a help? Bei Bedarf ist die Helligkeit mittels Potentiometer oder Fernbedienung anzupassen.

In the Power up OFF state the lighting will not be energised and the sensor will not operate during warm up period. Berkdr IK 04 Schutzart:

Комментарии
Отправить комментарий